You are here: Trace heating

Our flexible and adaptable electrical heat tracing systems are particularly well-suited for keeping your processes at the right temperature. The areas of application are as varied as your processes. Regardless of whether you wish to protect a medium

You can find out more here.

Electrical trace heating on pipes can be utilised with the various heating systems cited above. The experienced heating specialist is well aware of how to weigh up the advantages and disadvantages of the individual heating systems for the application case at hand, in order to implement the

You can find out more here.

Pre-insulated pipes are usually used for longer pipe routes above ground for cost reasons. Following pipe installation, the heating cables are drawn into the narrow, empty conduit previously fitted on the pipe beneath the

You can find out more here.

Electrical trace heating for long pipes is laid in triple or multiple configurations as a three-phase heating circuit. In this way, pipes 2-3 km in length can be realised with just one or two heating circuits and with

You can find out more here.

We supply connection-ready heating hoses for measuring and analysis lines in a range of designs and lengths, in accordance with customer specifications. Depending on the purpose of use and the design temperature, the heating hoses generally consist of a measuring line produced from plastic or stainless steel and are

You can find out more here.

Electrical pump heating is used for heating and temperature-maintenance of the pump body. This can be implemented by various heating systems, e.g. with heating tapes, heating cables or in complex cases with

You can find out more here.

Aeration and ventilation valves on the tank, industrial fittings, regulation and shut-off valves, rotary valves, etc. require electrical trace heating for heating and temperature maintenance. This technology has already proven itself. The sealing surfaces are kept

You can find out more here.

Electrical vessel heating is used in order to maintain the temperature in upright and horizontal vessels. In general, only the bottom half or the lower section is fitted with heating cables. For ease of installation, the heating cables are fastened with

You can find out more here.

Electrical tank heating is used for temperature maintenance. A range of heating technologies exists. One possible solution is to fit the heating cable with assembly tape in a meandering format in multiple heating rings above each other from the outside on the tank wall, whereby the

You can find out more here.

Electrical silo heating serves to control the temperature of the silo walls, in order to prevent a drop below the dew point and with it a baking-on of the product due to the formation of condensate. For this purpose it is necessary to fit the entire silo wall with heating cables and subsequently with

You can find out more here.

Electrical filter heating is generally only used for the filter cone, in order to keep this at the desired wall temperature to avoid drops below the dew point. This prevents the clumping or baking on of usually aggressive

You can find out more here.

As with filter systems, electrical heating for pneumatic and mechanical screw conveyors is used in order to prevent drops below the dew point. Due to the solid

You can find out more here.

Loading arms are pre-heated to the desired temperature and their temperature is maintained by electrical trace heating. It is particularly important here that the swivel joints are also included in the

You can find out more here.

Electrical heating systems for tankers and containers facilitate a slow increase in temperature, i.e. heating and temperature maintenance at the required product holding temperature of up to 200 °C. Heating can

You can find out more here.

Electrical heating mats are always used if it is necessary to reduce the assembly times on the construction site for a range of reasons. Various heating systems are used with the heating mats

You can find out more here.

Our heating cables for outdoor surface heating systems are superbly well-suited for defrosting ice and snow outdoors, as well as for concrete and sand installation for snow and de-icing for outdoor plants, e.g. in the oil and gas industry or in industrial

You can find out more here.

Electrical reactor heating is designed with high-temperature resistant, mineral-insulated heating cables, which are laid from the outside at a close distance to each other around the usually cylindrical vessel. Ideal is a smooth and clean

You can find out more here.

From simple contactor control to convenient thyristor control, we supply the right controls for your heating requirements. Power and temperature controls serve to monitor the heater for high temperatures, as well as controlling

You can find out more here.